Managed Industrial Gigabit Ethernet PoE+ Switch - (8) RJ-45, (4) SFP

• Economical switch delivers features normally found in more expensive switches.
• PoE 802.3af and PoE+ 802.3at compatible. Delivers up to 30W per port.
• SFP ports enable single-mode or multimode Gigabit fiber uplinks over long distances.
• Rated for extreme temperatures of -40 to +75° C.
• Dual DC power inputs for redundancy.
• IP30-rated housing is also rated for shock and vibration protection.
• Manage through a Web interface, SNMP, or command-line interface (CLI).
• Features bandwidth rate control, traffic prioritization, and quality of service.
• DIN rail or wall mount.
• Features bandwidth rate control, traffic prioritization, and quality of service.

PoE+ and SFP ports for flexibility.
This switch has eight 10/10/1000-Mbps PoE/PoE+ copper ports and four SFP ports for uplinks. This way you can power distant access points, security cameras, and other industrial equipment over the copper Ethernet lines at the far edges of your network where it's impractical to run electrical wires. The SFP fiber uplinks give you almost unlimited fiber distance options, depending on the SFP.

Maximize uptime.
Advanced management features help minimize network downtime by enabling you to remotely diagnose and manage network problems. And you'll eliminate the need to send IT technicians on site—thus lowering costs.
The switch is fully manageable through SNMP, a Web browser, Telnet. Control the bandwidth on each port individually and set up Quality of Service (QoS) priority queuing for critical applications.
The switch supports port-based VLAN and IEEE 802.1Q VLAN tagging, MAC-based trunking, IP-multicast IGMP snooping, rapid spanning tree for redundancy. Plus, it has 802.1x port-based authentication for security.

Fast failovers.
The switch gives you maximum network flexibility: Spanning Tree Protocol (STP/RSTP), Link Aggregation Control Protocol, and a ring protocol. It offers a 20 millisecond or less failover.

Extreme applications.
Encased in an IP30-rated metal case, this switch withstands extreme temperatures from -40°C to +75°C (-40° F to +167° F). Use it for:
Security and surveillance, particularly to backhaul IP security camera data.
Military applications, especially in ships and other vehicles.
Factory automation for controlling machinery, PLCs, motor drives, sensors, counters, inspection cameras, and packaging equipment.
Oil and gas fields or remote equipment monitoring and control.
Building automation for controlling HVAC and lighting systems.

Installation options.
The switch features redundant power inputs and includes DIN-rail and panel-mount kits. The power supplies (MDR-40-48 and SDR-240-48) are sold separately.

Approvals
CE; RoHS/WEEE; EN61000-6-2, EN61000-6-4;
Connectors
(8) RJ-45 ;(4) SFP
DHCP
Client, Server, Relay, Snooping, Option 82
Dimension
6”H x 5”W x 3” D (15.4 x 12.8 x 7.7 cm)
Failover
Link loss recovery < 20ms; Single and multiple rings supported
Flow Control
IEEE 802.3x full-duplex, Back-pressure half-duplex
Humidity
5 to 95% non-condensing
Indicators
LEDs: Power, Ethernet Port
Ingress Protection
IP30
Jumbo Frames
9K bytes
Link Aggregation
Static trunk or Dynamic via LACP (Link Aggregation Control Protocol)
Link Layer Discovery Protocol (LLDP)
IEEE 802.1ab
MAC Addresses
8K
Management
CLI, WEB-based Management; SNMP v1, v2c, v3; Telnet (5 sessions); HTTPs, SSH; Radius Client for Management; TFTP/FTP for Configuration Import/Export; TFTP/FTP for Firmware Upgrade;Syslog; RFC 1757 RMON 1,2,3,9; RFC 2674 Q-Bridge MIB; RFC-1213 MIB-II; RFC-1493 Bridge MIB; RFC 2233 IF MIB;DHCP; NTP/SNTP; PoE Management
Management Security
HTTPs; SSH; Radius client
MIBs
RFC 1757 RMON 1,2,3,9; RFC 2674 Q-Bridge MIB; RFC-1213 MIB-II; RFC-1493 Bridge MIB; RFC 2233 IF MIB
Multicast Protocols
IGMP v1, v2 with up to 255 multicast groups; IGMP snooping and querying; Immediate leave and leave proxy; Throttling and filtering
Network Redundancy
Fast failover protection rings: Link loss recovery < 20ms; Single & Multiple rings supported; Spanning Tree Protocol: IEEE 802.1D STP, IEEE 802.1w RSTP, IEEE 802.1s MSTP; Port Trunk with LACP: Static trunk or Dynamic via LACP (Link Aggregation Control Protocol)
NTP/SNTP
Yes
Operating Mode
Store and forward; L2 wire-speed, non-blocking switching engine
Operating temperature
-40 to 167° F (-40 to + 75° C)
PoE Management
Scheduling; power control; PoE PD power consumption
Port Security
IP and MAC-based access control; IEEE 802.1X authentication Network Access Control
Power
Redundant terminals, reverse power protection; 46-57 VDC; switch power consumption is 15W, total power consumption is 240W
QoS
8 queues IEEE 802.1p QoS; SPQ, WRR scheduling schemes; port-based shaping 8 queues IEEE 802.1p QoS; SPQ, WRR scheduling schemes; port-based shaping traffic
Security
IP and MAC-based access control; IEEE 802.1X authentication Network Access Control; Multicast/Broadcast/Flooding Storm Control
Spanning Tree Protocol
IEEE 802.1D STP, IEEE 802.1w RSTP, IEEE 802.1s MSTP
Storage Temperature
-40 to +185°F (-40 to +85° C)
System Status
Device info, status; Ethernet port status
Traffic Shaper
Port-based Port shaping
VLAN
IEEE 802.3x (Full Duplex) and Back-Pressure(Half Duplex) flow control; 256 Port-based VLANs; IEEE 802.1Q tag-based VLANs; IEEE 802.1ad Double Tagging (Q in Q)
Weight
0.7 lb. (.32 kg)

(1) Hardened Managed Ethernet Switch
(4) M3 Screws
(2) Panel Mount Brackets
(1) DIN Rail Clip
(1) 6 position Phoenix Connector
(4) RJ45 Ethernet-Port Dust Covers
(4) SFP Ethernet-Port Dust Covers